Kuvaus
Linkki valmistajan sivuille
canAnalyser 3 Suite
The canAnalyser is a powerful, multi-purpose analysis tool for the development, test and maintenance of CAN, CAN FD, LIN, CANopen, DeviceNet and SAE J1939 networks. The software package is modular, open and expandable.
Comparison of the CAN diagnosis devices
| Features | CBT2 | CANcheck | CANtouch | CANobserver |
| General Features | ||||
| CAN-Connector | 2 x SUB-D9 | 1 x SUB-D9 | 1 x SUB-D9 | 1 x SUB-D9 |
| Interfaces (PC, User) | USB | USB | USB | Ethernet |
| Other connectors | Trigger Out | Trigger Out | 1 x Switch | |
| User Interface | Windows SW | Graphic display | Touch-display | Webserver, Status LEDs |
| Measurement functions | ||||
| ID-scan for: CAN, CANopen, DeviceNet, SAE J1939 | X / O / O / O | X / X / – / – | O / O / O / O | X / X / X / X |
| Baud rate scan | X | X | X | X |
| Data export / Print function | X / X | PC, Terminal SW |
X / Screenshots | ETH / via PC |
| Power Supply | 24 VDC 110-240 VAC |
Battery, 4x AA |
Ext. / Accu | 9-36 VDC |
| Online monitoring | ||||
| Display bus status | X | X | X | X |
| Display bus traffic [%] | X | X | X | X |
| Display error frame counter (absolute / per second) | X / X | – / X | X / X | X / X |
| Display optional CAN supply voltage | X | X | X | X |
| Display shield voltage | – | – | X | – |
| Signal quality measurement per CAN-device | ||||
| Common mode voltage | – | – | X | – |
| CAN level absolute | – | X | X | – |
| CAN level difference (disturbance-free voltage) | X | X | X | – |
| Edge speed (in 1/64 of bit-time) | X | – | X | – |
| Integrated oscilloscope display | X | – | X | – |
| Cable testing | ||||
| Cable length | X | X | X | – |
| Termination resistor | X | X | X | – |
| Loop resistance | X | – | X | – |
| Short-circuits | X | X | X | – |
| Line breaks | X | X | X | – |
| Cable impedance | – | X | – | – |
| Measure optional power-lines on CAN-network | X | X | X | – |
| Continuous network-status monitoring | ||||
| Detect logic CAN errors (Error-frames, busload) | X | – | X | X |
| Detect physical CAN errors (Signal-quality) | X | – | O | X |
| Recording (data sets / time) | unlimited (optional) | – | O | 20 / 10 yrs. |
| Track display 4x physical, 4x logical | X | – | – | X |
| E-mail notification | X | – | – | X |
| Control center access (SNMP) | – | – | – | X |
| CAN monitor | ||||
| Transmission / reception of CAN telegrams | O / O | – / – | O / O | – / – |
| Support for CANopen decoding (receive only) | O | – | – | – |
| Online Trigger | ||||
| BNC-connector (e.g. for oscilloscope) | X | X | – | – |
| Error output (max. 30VDC, decoupled) | – | – | – | X |
| Trigger on CAN-Error-frames | X | X | – | X |
| Trigger on CAN-Identifier | X | X | – | – |
| Trigger on physical CAN errors | X | – | – | X |
